Plumbing for Beginners: The Essentials for Installing a Bathtub
Plumbing for Beginners: The Essentials for Installing a Bathtub
Blog Article
Everybody will have his or her own thinking when it comes to How to Install a Bathtub Yourself.
Setting up a bathtub isn't precisely rocket science, but it does require solid plumbing, carpentry, and also often, tiling abilities. Changing an old bath tub with a new one is likewise a moderately difficult job. If the old bathtub is easily easily accessible, the job can move easily; if you have to open up a wall to get rid of the old bathtub and place the new bath tub, the job is much harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to leave the old tub as well as set in the brand-new one. Make certain you have actually qualified yourself for the work as well as fit attempting it. Instead of working with a service provider to take control of a halfway-completed job, it is much better to consider employing one before you start. Opportunities are you might need a professional plumber to make tube connections.
This article will assist you mount a brand-new bath tub in your bathroom if you have currently purchased a brand-new bathtub as well as don't need to alter the setup of your previous water system pipes.
Your devices and also material list should comprise the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the water. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The procedure of eliminating the existing taps can be rather bothersome as a result of the restricted gain access to that is commonly the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the remaining water that will certainly originate from the pipes. When the supply pipelines have been gotten rid of, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning during this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing compound.
Prior to going on to fit the new faucets, compare the pipeline links on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, then you will need reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the tap in the mounting opening in the bath/basin making sure that the washers remain in area in between the faucet as well as the sink. Secure the tap in place with the producer offered backnut. As soon as the tap is securely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet connectors. The previous kind needs to be attached to the faucet ends initially, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Bathtub
Using both wooden boards under its feet, put the bath tub in the called for placement. The wood boards are valuable in equally spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four small factors.
The next goal is to guarantee that the bath tub is leveled all round. This can be achieved by examining the level and also readjusting the feet on the tub till the spirit level reads degree.
To install faucets, fit the bottom of the furthest versatile tap adapter to the proper supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the water supply as well as examine all joints as well as brand-new pipework for leaks and tighten them if necessary. Fill up the tub as well as also check the overflow outlet as well as the normal outlet for leaks.
Finally, repair the bath paneling as described in the maker's user's manual. Tiling and securing around the bath tub ought to wait till the bathtub has actually been used a minimum of once as this will certainly resolve it into its final placement.
Planning for the Installation
Firstly, the supporting framework provided with the bathroom needs to be fitted (if needed) according to the supplier's directions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be suited its final setting.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to break a rigid seal, triggering the water to permeate the wall surface between the bath as well as the tiling, leading to difficulties with dampness as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to securing, to permit the motion experienced when the tub is in use. The sealant can fracture fairly very early if you do not consider this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly offered on the market. It is advisable to fit the tiles making use of waterproof or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious reader on How to Install a Bathtub Yourself, I was thinking sharing that piece of content was necessary. Those who liked our article plz make sure you remember to share it. I treasure reading our article about A Step-by-Step Guide to Installing a Bathtub.
Pro assistance? Dial. Report this page